DS 430S Chip Forge/Brazing Hearth
The DS430S is a combined Ceramic Chip Forge and Brazing Hearth with fail safe controls. It is based on well proven Flamefast technology and is especially useful where space limitations are a consideration. The unit consists of a ceramic chip forge and a single brazing hearth usually equipped with a Flamefast RF80 brazing torch. The unit can be run on either Natural Gas or LPG bottled gas.
The forge has a single phase whisper quiet integral fan to provide the air supply and takes only 15 minutes to reach working temperature. It can reach a temperature of 1,500°C. It has a 340mm diameter working area and can work up to 50mm steel bar. The ceramic chip technology minimises surface scale formation.
The brazing hearth has an area of 0.23 square metres with a heavy duty refractory base. The RF80 brazing torch, which delivers up to 80,000BTU of heat output, can be replaced by a Flamefast RF10 jewellery torch for fine work. All Flamefast RF torches have a single hand-wheel control to give ease of flame control and a constant flame pattern over the range of flame sizes. The torches are ignited electronically.
As with all Flamefast equipment, the DS430S Chip Forge/Single Brazing Hearth is covered by the Flamefast unconditional 2 year warranty.
Dimensions
Height 1080mm, 1800 including Varivac extraction. Width 1040mm. Depth 550mm.
Forging
Performance
GAS TYPE |
RATE |
BTU/HR |
KW |
Natural Gas |
2.14m3/h |
77000 |
22.6 |
Propane |
1.26kg/h |
77000 |
22.6 |
Butane |
1.26kg/h |
77000 |
22.6 |
Standard Equipment
- Push-button no-volt release starter. Requires manual restart after power failure.
- Ceramic hearth.
- Automatic safety check of controls and air fan.
- Full manual control of hearth conditions.
- Whisper quiet air blower fan.
- Indicator status lights.
- Gas non-return valve.
- 12.5kg of ceramic chippings
- Operation/Instruction manual.
- Side and rear heat shields.
- Rake iron
Optional Extra
- Fume extraction equipment to meet the requirements of COSHH Regulations
According to the Health & Safety at Work Act 1974, BS 4163:2000 and COSHH Regulations it is mandatory that all fumes must be removed at source.
The DS 430S complies with British Gas standards and is a fully
failsafe system
Brazing
Performance
GAS TYPE |
RATE |
BTU/HR |
KW |
Natural Gas |
1.9m3/h |
70000 |
19.8 |
Propane |
1.1kg/h |
70000 |
19.8 |
Butane |
1.1kg/h |
70000 |
19.8 |
Standard Equipment
- 1 asbestos-free heat resistant refractory hearth.
- 2 full size Heat Reflective Blocks
- 4 half size Heat Reflective Blocks.
- Push-button no-volt release starter.Requires manual restart after power failure.
- 1 RF 80 brazing torch.
- Colour coded reinforced gas and air hoses.
- Whisper quiet air blower fan.
- Push button electronic ignition.
- Auto gas leak proving system on start up.
- Indicator status lights.
- Gas non-return valve.
- Operation/Instruction manual.
Optional Extras
- RF 10 Fine Jewellery brazing torch.
- 300mm revolving brazing table.
- Brazing kit.
- Fume extraction equipment to meet the requirements of COSHH regulations.
All sequences of operation are visually displayed using neon
indicators. On start-up the gas train, hoses and torches are tested
for escaping gas.
Leaks from any component will result in a continuously illuminated
red neon and the main flow of gas will be prevented from entering
the system.
Total Gas Performance
GAS TYPE |
RATE |
BTU/HR |
KW |
Pressure |
Natural Gas |
4.0m3/h |
147000 |
42.4 |
20 mbar |
Propane |
2.4kg/h |
147000 |
42.4 |
35 mbar |
Butane |
2.4kg/h |
147000 |
42.4 |
28 mbar |
Electrics |
120 watts – 220–240 volts single phase |
Weight |
151Kg |
Varivac Extraction
The unique fume intake configuration of the Varivac captures all fumes and prevents any spillage. An electrical interlock prevents the use of any linked equipment before the Varivac is switched ON. The Varivac can be fitted to existing equipment if required with a choice of low level or high rise exhaust outlets.
Performance 700 cfm per hood
Noise Level Average noise level 80 dB at 1 metre
Fully automatic systems available on request
